Use your pool long after the sunlight goes down thanks to our guide for replace a puddle luminance .
Cherdchanok Treevanchai / Getty Images
Safety Precautions
It ’s necessary to note that this job involves act with electric equipment in close proximity to an open dead body of piddle . Without proper precautions , there is a hazard of inadvertent electrocution , so it ’s essential to take the appropriate stair toturn off the powerand verify that the power is off before you lead off . Typically the syndicate equipment will connect to a judge breaker permutation on the principal electric gore , though in some cases , the pool will have a dedicated electric panel where you could plow the power off .
Additionally , when working around the puddle , it ’s of import to walk slowly and cautiously to invalidate fall away or tripping . A wet deck can position a important hazard when your care is focused elsewhere , so apply a towel to wipe up any H2O in your work area . Also , check that to keep track of tools , fasteners , and other equipment in the locality .
What You’ll Need
Equipment / Tools
Materials
Instructions
How to Change a Pool Light
Turn Off the Power
Before undertake to get rid of the pool brightness regular , you require to turn off the big businessman to the kitty light and pocket billiards equipment . Head to the circuit breaker box for the home and place the switch that controls the puddle equipment . If the switching is not on the main breaker box , the pocket billiards may have a dedicated circuit breaker loge where you’re able to exclude off the power . Flip the breaker substitution to turn off the power .
Turn on the pool light if you have more than one and activate the pool heart to verify that the power is off . If the magnate has successfully been shut down to the consortium equipment , then the pump and pool lights will not turn on .
Remove the Pool Light Fixture
Some DIYers may be able to unscrew the pool illumination fixture without getting in the pool , but if the light is too low on the side of the puddle , or your arm is n’t longsighted enough to reach , you may need to get into the puddle to loosen the piece of ass at the top of the fixture , known as the screw - lock .
Next , use aflat - head teacher screwdriverto carefully pry the light fastness out of the light box . Work around the light until it is loose enough to take hold of with your digit , then deplumate the idle fixture out of the wall .
Pull the Light Fixture Onto the Pool Deck
While the light fixture is still in the pond , chink for buoyancy by allowing it to float on the water . If the housing does not drift or seems to have water system in it , this is the likely causal agent of the light burning out . scrutinise the caparison for any cracks or obvious sign of damage . If the trapping appear fine , the gasket may need to be replaced .
Raise the pool light housing out of the consortium and onto thepool deck . pass over up any water in the domain , then dry out the light-colored fixture , your hands , and any tools you will be using . If moisture gets into the light fixture during this repair , the new bulb may infract in brief after rick it on .
Take Off the Light Fixture Cover and Lens
Depending on the age and model of the puddle visible light , you may need to transfer several screws to loosen the light repair cover . Newer pool light source are typically secured by check that can be pried loose , instead of turnkey . Undo the light reparation fasteners to remove the back .
Next , take out the gasket and lens to reveal the electric-light bulb . Before proceeding , visit the gasket for sign of wear . If necessary , dispose of the old gasket and replace it with a unexampled gasket .
Replace the Light
Now that the bulb is exposed , go forward and hit it from the light fixity . The oil from human hand can damage the bulb , have it to break prematurely , so when you are set up the novel lightbulb , accommodate it with a newspaper towel or a microfiber textile , being careful to annul touching the bulb directly with your pelt .
Reassemble the Light Fixture
After changing the lightbulb , substitute the gasket if necessary , then reassemble the faint fix housing . Work slowly to control that the composition of the visible radiation are order properly to avoid any gaps in the housing .
Secure the light fixture using the screws , tabs , or other fasteners that were antecedently remove . When you are confident that the lodging is watertight , place it into the pool water to find out the buoyancy . If done aright , the lodging will float and no water will enter the lightsome mending .
Reinstall the Pool Light Fixture
Slide back into the pool , if necessary , then coil the cable around the base of the fixture before inserting the Inner Light back into the wall . Hold the fix in situation as you guarantee the light to the wall using a screwdriver and the screw - lock fastener that was originally transfer .
Turn the Power On and Test the Pool Light
Climb out of the pool and dry out off , then head to the electrical panel . Turn on the pool surf switch to restore great power to the pocket billiards lighter and pool equipment . Once the power is back on , test the light to make certain that it is working properly .
Credit:Cherdchanok Treevanchai / Getty Images
